Fab 101 - TIG Welding

A few months ago, we introduced you to the processes involved with MIG welding. MIG welding, or metal inert gas welding, is a tool of the trade for millions of fabricators around the world because of its various advantages over other forms of welding. MIG welding is fairly easy to learn, equipment is reasonably priced, and it allows users to lay down a fast bead. However, these advantages are not for everyone. Some fabricators want a little more control and precision in their welding, which is why they opt for TIG welding.

TIG welding, or tungsten inert gas, is a process in which a tungsten electrode heats the metal you are welding, while Argon gas protects the weld puddle from airborne contaminants. It’s a clean process. However, it can be fairly frustrating for first-time users because of the precise coordination required from your hands and feet. Some eventually give up and stick with MIG welding.

Although it is more labor intensive and requires more skill, it is often used by those looking for the ultimate in control and to produce super-clean welds. This includes most motorsports teams. TIG welds often are found on some of the top race machinery in the Dirt Sports Nation. There’s a lot to learn in order to lay down some perfect beads, so we headed down to The Fab School in Riverside, California, to get tips and a quick look at the basics of TIG welding from Troy Johnson.

The Machine

Before you can start laying down the perfect bead, you’re going to need a machine and power source that will allow for the high amperage TIG welding requires. The typical 110-volt outlets in your garage will not supply enough power to the machine. Instead, you will need a 220-volt outlet. As far as picking a machine goes, there are many companies to choose from. The Fab School chose Miller welding products, like the Sycrowave (pictured here) and the Dynasty.

Air-Cooled VS. Water-Cooled

“If you want to purchase a welder, you don’t have to go broke buying one,” explains Johnson. “The difference between an air- versus a water-cooled machine is about $1,500. If you’re not going into production, an air-cooled machine will suit your needs and run about $3,000. If you are going into some sort of production, a water-cooled machine is required and will run you about $5,000.” As you can see from this photo, there aren’t a lot of dissimilarities between the water-cooled torch on the left, and the air-cooled torch on the right.

Prepare the Tungsten

Prepare a new or unsharpened tungsten by grinding it to a point first. For best results, use a 200-grit or finer grinding wheel. Also, it’s important to only use that grinding wheel for sharpening your tungsten. This ensures the tungsten will not become contaminated, resulting in lower-quality welds. Troy also likes having his students roll the edges of the tungsten after it’s sharpened to a point.

Install the Tungsten

Once the tungsten is sharpened, slide it back into your torch. Before you tighten it up, though, be sure it is at the correct depth inside the torch. Your tungsten should stick out no more than the diameter of your cup (the pink park in this photo). If the tip of your tungsten has turned blue after welding, your tungsten is out too far.

Body Positioning

“A lot of muscles move when we reach out in front of us and pulling straight to our chest,” explains Johnson. “That requires a lot of work from your muscles. When sitting on the bench, I like to place the part I’m about to weld parallel with my chest. By doing so, I won’t have to move a whole lot once I start to weld. I also like to rest both of my hands because you have to be comfortable at all times. For a tall project (pictured here), I like to set up objects that allow my hands to be comfortable.”

Light It Up

Now, it’s time to start laying down some beads. First, hold the torch in your dominant hand at about 70 to 80 degrees. In the other hand, hold your filler rod at a 15-degree angle. Once you make an arc by placing your foot on the pedal, it’s go time. A lot of first timers have the tendency to pulse the pedal, but this is not correct. Once you start to heat your material and build up the puddle with your filler rod, you then drag it out. So, fill it up, and then drag it out. By doing so, Troy says your puddle will always be constant. This step requires a lot of practice because of all the control is put into your pedal, the angle and distance you hold your torch, and the amount of filler rod you dab into the heat.

The Good

If you’re a TIG welding prodigy, your welds will look as good as these.

The Bad

However, if your welds look like this, it’s time to keep practicing. Practice makes perfect! As you can tell by reading this, TIG welding is not an easy process, and these are just the basics. However, if you’re feeling confident and want to learn more about TIG welding, head on down to the Fab School and sign up for some of the courses.